background image

VSC8634/VSC8664 Evaluation Board

VPPD-03084 VSC8634/VSC8664 User Guide Revision 1.1

2

2

Introduction

The VSC8664 device is a low-power, quad-port Gigabit Ethernet transceiver with four SerDes interfaces 
for quad-port dual media capability. It includes an integrated quad port I C multiplexer (MUX) to control 

2

SFPs or PoE modules. The VSC8664 includes two recovered clock outputs to support Synchronous 
Ethernet applications.

This document describes the architecture and usage of the VSC8664 Evaluation Board (VSC8634
/VSC8664EV). The board may be used to evaluate a family of devices which include the VSC8634, 
VSC8662, and VSC8664. These devices vary with respect to the number of ports, supported interfaces, 
and available features. This document specifically addresses the VSC8664 device. The Quick Start section 
describes how to bring-up the evaluation board along with install and run the graphical user interface 
(GUI), used to control the evaluation board.

Figure 1 • VSC8634/VSC8664EV Evaluation Board

2.1

References

The following reference documents provide additional information about the operation of the VSC8574 
evaluation board.

VSC8634 Datasheet 
VSC8662 Datasheet
VSC8664 Datasheet
VSC8664 Evaluation Board Package 
VSC8664 GUI 

Summary of Contents for VSC8634














Reviews: