micronit microfludics FLUIDIC CONNECT 4515 User Manual Download Page 16

Page: 16 / 19

5.2

STAINLESS STEEL / TEFLON CONNECTION KIT

The tips and tricks in this section are related to the Fluidic Connect in combination with the

Stainless Steel or Teflon Connection Kit.

I connected all components according to the manual, but the connections still leak. What can be wrong?

1. Make sure the connections are finger tight (see 5.1. Tightening Force), if so DO NOT

tighten the connections any further, it might break the chip.

2. Check if there is no tension on the tubing, causing the tubing to exert a force on the seal.

3. If the tubing exceeds the ferrule edge, this can cause the problem, see figure 5.2.

Fluidic Connect 4515 - User Manual V1.5

F e r u l l e a n d
tube incorrect
assembled

Figure 5.2. Assembly of tubing and ferrule

Summary of Contents for FLUIDIC CONNECT 4515




















Search results

Summary of Contents for FLUIDIC CONNECT 4515

Reviews:

Related manuals for FLUIDIC CONNECT 4515

Brands by name

Popular brands

micronit microfludics FLUIDIC CONNECT 4515, User Manual

Search results

Summary of Contents for FLUIDIC CONNECT 4515

Reviews:

Related manuals for FLUIDIC CONNECT 4515

Brands by name

Popular brands