background image

10

The bell reset time mode enables you to
re-program the length of time you wish
the siren to sound after it has been
activated. 
The bell reset time is set by the factory to
10 minutes but this can be changed to a
choice of 7 other times to suit you. 
The legal maximum time under current
legislation is 20 minutes, please confirm
with your local authority for local by-laws.

BELL RESET

Then P

Prre

essss  P

P  4

4  EE  and within 5

seconds your choice.
((IIff  yyo

ou

u  d

do

o  n

no

ott  d

de

ecciid

de

e  w

wiitth

hiin

n  5

5

sse

ecco

on

nd

dss,,  tth

hrre

ee

e  ssh

ho

orrtt  b

blle

ee

ep

pss

w

wiillll  b

be

e  h

he

ea

arrd

d  a

an

nd

d  yyo

ou

u  w

wiillll

h

ha

avve

e  tto

o  e

en

ntte

err  P

P  4

4  EE  a

an

nd

d  sstta

arrtt

a

ag

ga

aiin

n..))

Then P

Prre

essss  P

P  0

0  EE  tto

o  e

exxiitt

p

prro

og

grra

am

mm

miin

ng

g..

1

4

3

2

TO CHANGE PASSWORD

The panel comes factory set to a standard 4-digit password 11112

22

2. This password code is the signal by

which the panel recognises a legitimate user. We recommend that you change this code to a 4-digit
password code of your own choosing. Each member of your family or household will have to know this
code and how to use it. 
To change the factory set code:

P

Prre

essss  P

P  11112

22

2  EE  tto

o

e

en

ntte

err  p

prro

og

grra

am

mm

miin

ng

g..

Status LED flashes.

3

1

EE

??

??

??

??

SETTING UP CHECK LIST

Have you done the walk test

Have you done the bell test?

Have you set your preferred entry time?

Have you set your preferred exit time?

Have you set your preferred bell reset time?

Have you changed your password?

2

After activation of the alarm system, the
external siren will stop after the
programmed time, but the internal siren
will bleep slowly until the password has
been entered.

If for any reason the sirens sound,
p

prre

essss  11112

22

2  to disarm.

For example, to change the
bell reset to 15 minutes (see
choices in Table): 
P

Prre

essss  P

P  11112

22

2  EE  tto

o  e

en

ntte

err

p

prro

og

grra

am

mm

miin

ng

g..

P

Prre

essss  3

3  EE  which is the

program for 15 minutes.
If entered correctly, a
continuous bleep will be
heard for 2 seconds.

P

Prre

essss  P

P  11  EE  

YYO

OU

U  M

MU

USSTT  N

NO

OW

W  U

USSEE  TTH

HEE  N

NEEW

W  P

PA

ASSSSW

WO

OR

RD

D  FFO

OR

R  A

ALLLL  A

AC

CTTIIO

ON

NSS..

You have 10 seconds
to enter the new 4-
digit password plus EE. 
After the keys are
pressed an
acceptance tone of 2
seconds duration will
be heard.

P

Prre

essss  P

P  0

0  EE tto

o  e

exxiitt

p

prro

og

grra

am

mm

miin

ng

g..

4

Example:

Choices are:
11EE

5 minutes

2

2EE

10 minutes

3

3EE

15 minutes

4

4EE

20 minutes

5

5EE

1 minute

6

6EE

2 minutes

77EE

3 minutes

8

8EE

4 minutes

www.ukpanels.com

Summary of Contents for MM23207













Reviews: