background image

ii

MRX-900 Operating Manual

MRX-900

900 MHz
Spread-Spectrum
Wireless Modem

This manual contains information of proprietary interest to
Microhard Systems Inc.  It has been supplied in confidence to
purchasers and users of the MRX-900, and by accepting this
material the recipient agrees that the contents will not be copied
or reproduced, in whole or in part, without prior written consent
of Microhard Systems Inc.

Microhard Systems Inc. has made every effort to assure that this
document is accurate and complete.  However, the company
reserves the right to make changes or enhancements to the
manual and/or the product described herein at any time and
without notice.  Furthermore, Microhard Systems Inc. assumes
no liability resulting from any omissions in this document, or
out of the application or use of the device described herein.

Microhard Systems’ products are appropriate for home, office,
or industrial use, but are not authorized for utilization in
applications where failure could result in damage to property or
human injury or loss of life.

The electronic equipment described in this manual generates,
uses, and radiates radio frequency energy.  Operation of this
equipment in a residential area may cause radio interference, in
which case the user, at his own expense, will be required to take
whatever measures necessary to correct the interference.

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received including
interference that may caused undesired operation.

M

icrohard

I

S

nc.

ystems

Leaders in Wireless Telecom

#209 - 12 Manning Close N.E.
Calgary, Alberta  T2E 7N6
Phone: (403) 248-0028
Fax: (403) 248-2762
www.microhardcorp.com

© 1998 by Microhard Systems Inc., All Rights Reserved.
MRX-900 is a registered trademark of Microhard Systems Inc.
HyperTerminal is copyrighted by Hilgraeve Inc, and developed for Microsoft.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
pcANYWHERE and Symantec are registered trademarks of Symantec Corp.
All other products mentioned in this document are trademarks or registered
trademarks of their respective holders.
Manual Revision 1.0, June 20, 1998.

Summary of Contents for MRX-900

































Reviews: