Microframe Corporation
Series 3007 - DataPage Lite Transmitter
10
5 GEO PULSAR USER GUIDE
5.1 TURNING ON THE PAGER
Hold down the “LARGE BLACK BUTTON”
until the pager comes on.
5.2 SENDING A PAGE
When the transmitter is turned on, the
prompt “PAGER (1-9999)” appears on the screen.
To send a page, enter the pager number on the
transmitter’s number pad followed by the
“SEND” key.
5.3 SENDING AN ALPHA MESSAGE
To send a pre-defined message to a pager,
enter the pager number followed by the “EN-
TER” key. You will be prompted for a “BEEP
TYPE (1-4).” Select 1-3 here and press the
“SEND” key. If no number is chosen, the pager
will default to Beep Type 4 (“PAGING”).
5.4 SENDING A NUMERIC MESSAGE
To send a numeric message to a pager,
simply enter the pager number followed by the
“ENTER” key. The transmitter screen will
display “BEEP TYPE.” Simply press “ENTER”
to bypass this. The transmitter screen will then
display “ENTER MESSAGE.” Using the num-
ber keys, enter up to a 16-digit numeric mes-
sage followed by the “SEND” key.
Note: Since
a numeric message is entered after the “BEEP
TYPE,” (pre-defined message) prompt, the alpha
message selected will be ignored.
5.5 RECEIVING A PAGE
The GEO Pulsar will start to vibrate when it
is paged. No action is necessary on the receiv-
ing end at this point. The pager will stop
vibrating after approximately 8 seconds. If the
user would like to stop the vibration before the
8 seconds, simply press the “LARGE BLACK
BUTTON.” If a numeric message is sent to the
pager, the message will be visible on the pager
screen until the pager stops vibrating. To view
the message after the pager has stopped vibrat-
ing, press the “LARGE BLACK BUTTON” once.
5.6 SENDING A GROUP CALL PAGE
All pagers respond to call number “900”
(unless another group call number has been
chosen). To page all pagers at once, simply
enter “900” and “SEND.”
5.7 MANUAL PAGER TURN-OFF
Press the “RIGHT ARROW BUTTON.” The
words “PGR OFF” will appear on the LCD
screen. Press the “LARGE BLACK BUTTON”
once to confirm.
NOTE: If you have chosen to
disable the pagers’ on/off button, the pagers can
only be turned off from the transmitter.
5.8 PAGER TURN-OFF FROM BASE
Enter the pager number followed by the
“ENTER” key. Press “ENTER” again to bypass
“BEEP TYPE” screen. When screen reads
“ENTER MESSAGE,” enter the message code
“
((123456
” followed by “SEND.”
NOTE: The
two left parenthesis before the number
are required, or it will not work. This "("
symbol is located to the left of the "0" key
and beneath the "7" key.
Since all pagers respond to call number
“900,” paging “900” with the message code
“
((123456
” will turn all pagers off.
5.9 POWER CHECKING
When the battery level is low, a low-battery
symbol will appear at the bottom of the pager
screen.
5.10 LIGHTING FUNCTION
Pressing the “LEFT ARROW BUTTON” for
one second can turn on the backlight on the
LCD screen. The light will shut off automati-
cally after approximately 10 seconds, or the
user may turn the light off manually by press-
ing the “LEFT ARROW BUTTON” once.
5.11 CAUTION
a)
The pager is made up of LCD and
precision elements. Avoid water and
high temperature.
b)
Remove the battery if the pager will not
be in use for a long period of time.
c)
If the pager is not working properly, do
not dismantle or repair it yourself.
