Microchip Technology PIC24FV16KM204 FAMILY Datasheet Download | Manualshive

Page: 67 / 336

background image



2013 Microchip Technology Inc.

Advance Information

DS33030A-page 67

PIC24FV16KM204 FAMILY

5.0

FLASH PROGRAM MEMORY

The PIC24FV16KM204 family of devices contains
internal Flash program memory for storing and execut-
ing application code. The memory is readable, writable
and erasable when operating with V

DD

over 1.8V.

Flash memory can be programmed in three ways:
• In-Circuit Serial Programming™ (ICSP™)
• Run-Time Self-Programming (RTSP)
• Enhanced In-Circuit Serial Programming

(Enhanced ICSP)

ICSP allows a PIC24FV16KM204 device to be serially
programmed while in the end application circuit. This is
simply done with two lines for the programming clock
and programming data (which are named PGCx and
PGDx, respectively), and three other lines for power
(V

DD

), ground (V

SS

) and Master Clear/Program Mode

Entry Voltage (MCLR/V

PP

). This allows customers to

manufacture boards with unprogrammed devices and
then program the microcontroller just before shipping
the product. This also allows the most recent firmware
or custom firmware to be programmed.

Real-Time Self-Programming (RTSP) is accomplished
using

TBLRD

(Table Read) and

TBLWT

(Table Write)

instructions. With RTSP, the user may write program
memory data in blocks of 32 instructions (96 bytes) at a
time, and erase program memory in blocks of 32, 64 and
128 instructions (96,192 and 384 bytes) at a time.
The NVMOP<1:0> (NVMCON<1:0>) bits decide the
erase block size.

5.1

Table Instructions and Flash
Programming

Regardless of the method used, Flash memory
programming is done with the Table Read and Write
instructions. These allow direct read and write access to
the program memory space from the data memory while
the device is in normal operating mode. The 24-bit target
address in the program memory is formed using the
TBLPAG<7:0> bits and the Effective Address (EA) from
a W register, specified in the table instruction, as
depicted in

The

TBLRDL

and the

TBLWTL

instructions are used to

read or write to bits<15:0> of program memory.

TBLRDL

and

TBLWTL

can access program memory in

both Word and Byte modes.
The

TBLRDH

and

TBLWTH

instructions are used to read

or write to bits<23:16> of program memory.

TBLRDH

and

TBLWTH

can also access program memory in Word

or Byte mode.

FIGURE 5-1:

ADDRESSING FOR TABLE REGISTERS

Note:

This data sheet summarizes the features of
this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on Flash pro-
gramming, refer to the

“PIC24F Family

Reference Manual”

,

Section 4. “Program

Memory”

(DS39715).

24 Bits

Program

TBLPAG Reg

8 Bits

16 Bits

Using

Byte

24-Bit EA

1/0

Select

Table
Instruction

Counter

Using

User/Configuration
Space Select

Working Reg EA

0

Program Counter

0

«
...
65
66
67
68
69
...
»

Summary of Contents for PIC24FV16KM204 FAMILY

















































































































































































































































































































































Reviews:

No comments

Related manuals for PIC24FV16KM204 FAMILY

Brand: Magnescale Pages: 3

Brand: Eaton Pages: 96

Brand: IDTECK Pages: 12

Brand: Banner Pages: 2

CGLine+ Web Controller

Brand: Eaton Pages: 28

CentriPro Aquavar SOLO

Brand: Xylem Pages: 48

Brand: IBM Pages: 214

Brand: Trane Technologies Pages: 8

Brand: Auber Pages: 3

Brand: A10 Networks Pages: 2

Brand: Vageo Pages: 2

Brand: DirectConnect Pages: 2

Brand: QSC Pages: 13

Brand: Holars AS Pages: 15

Brand: METRON Pages: 34

PROFOX PF-M100X

Brand: AUMA Pages: 56

Brand: SUNWIND Pages: 53

Brand: Warner Electric Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands