background image

Operation

 2012-2014 Microchip Technology Inc.

DS50002081B-page 17

2.4

TARGET COMMUNICATION CONNECTIONS

2.4.1

Standard Communication Target Connection

Using the RJ-11 connector, the MPLAB ICD 3 In-Circuit Debugger is connected to the 
target device with the modular interface (six conductor) cable. The pin numbering for 
the connector is shown from the bottom of the target PCB in 

Figure 2-3

FIGURE 2-3:

STANDARD CONNECTION AT TARGET

2.4.2

Target Connection Circuitry

Figure 2-4

 shows the interconnections of the MPLAB ICD 3 In-Circuit Debugger to the 

connector on the target board. The diagram also shows the wiring from the connector 
to a device on the target PCB. A pull-up resistor (usually around 50 k

) connected from 

the V

PP

/MCLR line to the V

DD

 is recommended so that the line may be strobed low to 

reset the device.

FIGURE 2-4:

STANDARD CONNECTION TARGET CIRCUITRY

Note:

Cable connections at the debugger and target are mirror images of each 
other, i.e., pin 1 on one end of the cable is connected to pin 6 on the other 
end of the cable. Se

Section B.5.2.3 “Modular Cable Specification”

.

1

2

3

4

5

6

Target

Connector

Target

Bottom Side

PC Board

V

PP

/MCLR

Vss

PGC

V

DD

PGD

LVP

V

DD

V

PP

/MCLR

PGC

PGD

V

SS

AV

DD

AV

SS

2

1

5

4

3

User Reset

50K

Interface

Connector

Application

PCB

Device

Summary of Contents for MPLAB ICD 3





















Reviews: