manualshive.com logo in svg

Microchip Technology ADM00902, User Manual

Share
Download
Microchip Technology ADM00902 User Manual Download Page 11

ADM00902

 DEMONSTRATION BOARD

 FOR EMC2103 USER’S GUIDE

 2019 Microchip Technology Inc.

 

DS50002905A-page 11

Chapter 2.  Installation and Operation

2.1

INTRODUCTION

This section describes how to install the Microchip Thermal Management Utility GUI 
required in order to interact with the ADM00902 Demonstration Board.

2.2

SYSTEM REQUIREMENTS

The ADM00902 Demonstration Board is designed to be used with a personal computer 
(desktop or laptop) running Microsoft

®

 Windows

®

 7 or later. For USB connectivity, the 

minimal physical requirement for the PC is a standard type-A USB 2.0 port.

2.3

MICROCHIP THERMAL MANAGEMENT UTILITY GUI INSTALLATION

Go to 

www.microchip.com

, search for EMC2103-4 and download the Thermal 

Management Utility (Version 1.5.7 or newer).
If an older version of the software is already installed, you must remove it before 
installing the new one.
Follow the next steps to proceed with the installation.

FIGURE 2-1:

Thermal Management Utility – Setup Window.

Click the 

Next

 button to continue.

Summary of Contents for ADM00902























































Reviews:

No comments

Brands by name

Popular brands

Load more brands