manualshive.com logo in svg

Micro Seven VM10a, Operator'S Manual

Share
Download
Micro Seven VM10a Operator'S Manual Download Page 30

  

30

Chapter 10 

Stand-alone operation 

 

 

Voice/sound triggered measurement mode 
 
Pushing MIC TRIG button switch displays setting for microphone triggered measurement. The 
first digit indicates whether voice/sound trigger is enabled when it is blank. It is disabled when it 
is “1”. The next three digits indicates microphone sensitivity with 000 (most sensitive) and 255 
(least sensitive). As a factory condition, you will see 1032 which shows the voice/sound trigger 
is disabled. While pushing MIC TRIG switch, push ON/OFF momentarily. The number is 
changed to 032 to enable voice/sound trigger. Release MIC TRIG switch. Shout some word in 
front of microphone area under banana jacks on VM10 front panel. You will hear voiced 
measurement value from the speaker. 
 
To change the microphone sensitivity, push UP+ or DOWN- while MIC TRIG switch is pushed. 
For example, push DOWN-to obtain about 015 while pushing MIC TRIG switch to increase 
microphone sensitivity to trigger in less sound. Release MIC TRIG switch. Then shout any word 
away from VM10. You may hear voiced measurement. 
 
Push MIC TRIG button switch and push ON/OFF switch to disable the voiced measurement by 
seeing 1 in the first displayed digit. 
 
Value triggered measurement mode 
 
Pushing VALUE TRIG switch displays whether value-change trigger mode is enabled when the 
first digit display is blanked or value-change trigger mode is disabled when the first digit display 
shows “1”. While pushing this switch, push ON/OFF switch to change to enabled or disabled. 
The last three-digit displays value-change triggering level. Push UP+ or DOWN to change the 
trigger level while pushing this switch. 
 
As a factory condition, the value trigger mode is disabled. Push the ON/OFF switch while 
pushing VALUE TRIG switch to enable this mode.  
Set measurement mode to 2volt DC mode by pushing mode and range switches. The 
measurement indicates close to .000. Then apply 1VDC or similar value across VHI and VLO 
banana jacks. You will hear voiced measurement of data. 
Input voltage needs to be returned to close to zero volt to reset value trigger mode. 
Continuously applying same value across banana jacks will not produce voiced measurement. 
 
In resistance measurement mode, the trigger value is less value to trigger voiced measurement. 
This is opposite from DC volt and AC volt modes. For example, if value triggered measurement 
is enabled in resistance mode, shorting VHI and VLO banana jacks produces voiced 
measurement.  
 
There is no value triggered measurement mode in temperature mode. 
 

Front-panel controls: 
 

Summary of Contents for VM10a

































Reviews:

No comments

Brands by name

Popular brands

Load more brands