MICRO-EPSILON scanCONTROL 25 Series Assembly Instructions Manual Download Page 12

www.micro-epsilon.com

MICRO-EPSILON Messtechnik GmbH & Co. KG

Koenigbacher Str. 15

94496 Ortenburg / Germany, Tel. +49 (0) 85 42/1 68-0

Your local contact: 

www.micro-epsilon.com/contact/worldwide/

X9771413-A022061DTa

13. 

Unpacking, Included in Delivery

 - 1 scanCONTROL 25xx sensor with integrated controller
 - 1 PCR3000-5 multifunction cable, length 5 m; for power supply, trigger and RS422; 

M12x1 screw connector and free cable ends

 - Calibration protocol / assembly instructions
 - 2 Protective caps

14. 

Additional Information

Please refer to

 - the enclosed online documentation
 - the “Status and Error Messages“ and “Notes“ sections in the scanCONTROL  

Configuration Tools operating instructions.

You will find details about the individual programs in the respective operating  
instructions or in the operating instructions of this sensor, Chap. 6.2. 

 

You can find more information about the sensor in the operating instructions. 
They are available online at:

www.micro-epsilon.com/download/manuals/man--scanCONTROL-25xx--en.pdf

Summary of Contents for scanCONTROL 25 Series













Reviews: