Micom EDM MM50 Installation Instructions Manual Download Page 24 | Manualshive

Page: 24 / 26

background image

MODEL: EDM MM50 & MM80
MAGNETIC LINEAR SLIDING DOOR OPERATOR

Page 24

6.2 Applicable Door Size

MM50 & MM80

Rail Length (mm)

Entrance Width (mm)

Standard Size Option

Single - Left /

Right

1666 / 1925 /
2232 / 2512 /

2710

833 / 962.5 / 1116 / 1256 / 1355

Cut to Size (Made to Order)

Single

1500 - 1800

750 - 900

1801 - 2200

900 - 1100

2201 - 2710

1100 - 1350

2711 - 3200

1355 - 1600

7. Electronic Lock (Option)

NOTE: E-Lock is available with AUTO type only. Assist type
does not support E-Lock. E-Lock offers LK1 FAILSAFE
(UNLOCK without power) function only.

If an E-lock is fitted, it is not possible to open the door by hand. The
door will be unlocked upon an activation signal to the controller and
open automatically. Once a full open and close cycle has been
performed, the door will lock with E-lock once fully closed.

If there is a problem with the E-Lock, the controller will show this
when either in teaching mode or during normal operation.

7.1 Teaching with E-Lock

LED will flash RED with Buzzer.

Lock output Signal
(Option

– With Counter)

Wiring:
Red

– Lock output

signal
Black

– Com

Load Capacity: 0.3A /
AC125V / 1A / DC24V

E-Lock Harness

E-Lock Body

«
...
22
23
24
25
26
»

Summary of Contents for EDM MM50



























Reviews:

No comments

Related manuals for EDM MM50

Brand: Lincoln Electric Pages: 102

Brand: AUTO ARC Pages: 36

Auto Invision II

Brand: Miller Electric Pages: 132

Brand: LCN Pages: 5

Brand: WELDY Pages: 44

Brand: Walter Pages: 38

Brand: gala gar Pages: 67

BI-WELDER TIG 2040 DC-HF

Brand: Cebora Pages: 11

Brand: FAAC Pages: 60

Brand: Migatronic Pages: 44

Brand: Dictator Pages: 9

Brand: Dormakaba Pages: 23

Brand: Woodhaven Pages: 2

Brand: Heat&Glo Pages: 33

Brand: Blueweld Pages: 60

Brand: Dormakaba Pages: 11

CITOARC 2200 VRD

Brand: Oerlikon Pages: 92

Brand: Dormakaba Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands