background image

400-902-8288

Monday to Friday 8:30-17:30 (Closed on national holidays)

Sales / After-sales service

Registrant / manufacturer

Production address: No. 26, Xixi Road, Tianjin Free Trade Experimental 
Zone (Airport Economic Zone), Tianjin Neusoft Software Sticky Medical 
Doctor Valley 1st floor, ZX102
Accommodation: No. 26, Xixi Road, Tianjin Free Trade Experimental 
Zone (Airport Economic Zone), Tianjin Neusoft Software Sticky Medical 
Doctor Valley 1st floor, ZX102

Phone: 400-902-8288

Vendor: Miaomiaoce Medical Equipment (Tianjin) Co., Ltd.

Address: No. 26, Xixi Road, Tianjin Free Trade Experimental Zone 
(Airport Economic Zone), Tianjin Neusoft Software Sticky Medical 
Doctor Valley 1st floor, ZX102

Service

Customer service hotline

Dispose of the product, accessories, and batteries according 
to the city’s environmental protection regulations

Abandoned advice

Please store the thermometer in the storage set.

Please observe the following to prevent damage to the 
thermometer

Do not use ultrasonic to clean the thermometer

Do not soak thermometers in alcohol for long periods 
of time or try to disinfect them with hot water (water 
temperature 50

°C

 or higher)

Do not use benzene, thinner, gas, or other strong 
solvents to clean the thermometer

Do not store the thermometer in the following locations, as 
it may damage the thermometer

Wet environment
High temperature, high humidity, or direct sunlight
The area near the heating equipment, dusty, or high 
salt concentration in the air
Tilt, impact or vibration environment
Storage of chemicals or the presence of corrosive 
gases

Service hours

Summary of Contents for MMC-W501













Reviews: