manualshive.com logo in svg

Mi-T-M CM-1400-0MEC-DM, Operation Manual

Share
Download
Mi-T-M CM-1400-0MEC-DM Operation Manual Download Page 7

Operator’s Manual  

7

IMPORTANT SAFETY INSTRUCTIONS

WARNING:  To reduce the risk of injury, read this operator’s 

manual completely.  When using this product, the following 

basic precautions should always be followed:

1. Read all the instructions before using the product.
2. This product is equipped with a Ground Fault Circuit 

Interrupter (GFCI) in the power cord to reduce the risk 

of electrical shock.  If replacement of the plug or cord is 

needed, use only identical replacement parts.

3. Follow the grounding instructions included in this manual.
4. High pressure water spray can cut skin.  Do not direct 

spray at persons.  Keep operating area clear of all 

persons or pets.  Warn children that the water spray can 

cut.  Supervise children closely.

5. Do not allow children or untrained person to operate the 

washer.

6. Do not spray electrical switches, receptacles or light 

bulbs, or glass or fragile objects that may shatter.

7. Dirt and debris removed by spray can cause eye injury.  

Wear eye protection.

8. Wet surfaces can be slippery.  Wear shoes and keep 

both feet on the ground.  Do not climb on items being 

cleaned.  Do not overreach or stand on unstable support.  

Keep good footing and balance at all times.

9. When the spray trigger is released, water pressure 

is trapped in the discharge hose.  Release trapped 

pressure by triggering the spray gun after the washer is 

turned off.

10. Do not operate the washer when fatigued or under    

the influence of drugs or chemicals.  Stay alert.   

  

Watch what you are doing.

11. Follow the maintenance instruction specified in this

     

  manual.

SAVE THESE INSTRUCTIONS

WEAR PROTECTIVE CLOTHING

Wear close fitting clothing and safety equipment appropriate 

to the job.

Wear a suitable hearing protective device such as earmuffs 

or earplugs to protect against objectionable or uncomfortable 

loud noises.

Operating equipment safely requires the full attention of 

the operator. Do not wear radio or music headphones while 

operating machine.

Summary of Contents for CM-1400-0MEC-DM

































Reviews:

No comments

Brands by name

Popular brands

Load more brands