MG MERO 18 P Operating Instructions Manual Download Page 4

 

  

 

  
  

 

 

OPERATING INSTRUCTIONS  

Pneumatic Carton Stapler for coiled staples 

MERO 18 P + MERO 22 P

 

 

Page:  

4

 

Mod.: 

804 

 

ET      675, 676 

 

Page 4 of  6                           04.05.2018 

 

 
Loosen screws (S) in magazine seat (6) and move right (R) 
and left (L) stapling plate outward for long leg length (18) 
and inward for short leg length (15). Fasten screws (S) 
again.  
 
 
 
 
 
 

3.5  Staple clinch control (closed or open clinch) 

Should adjustment of the staple clinch be necessary, it 
should be carried out as follows: turn collar (3) with a matching tool (W), e.g. 2,5 mm rod, turn the collar 
(3) counter clockwise for a looser clinch, turn the collar (3) clockwise for a tight clinch. For thick carton 
quality a looser clinch may be recommendable as the staple can penetrate deeper into the carton. 
 
 
 
 
 
 
 
 
 
 
 

 

3.6  Adjustment of penetration  

For adjusting the penetration of the anvils loosen front screw (F) by means of a 6 mm hexagon spanner 
(I). Move body up or down into the required position. Fasten front screw (F) again. If the body (2) is in 
the upper position, the stapling penetration (A) is maximal. If the body (2) is in the lower position, 
penetration (B) is minimal. 

 

 

 

 

 

 

 Tight clinch 

 Looser clinch 

Middle position for optimal clinch 

 

A = penetration adjustment 
B = anvil 
C = staple  

           Tight clinch 

         offene Heftung 

 

open clinch 

open clinch

 

Summary of Contents for MERO 18 P












Reviews: