MFJ Super Hi-Q Loop Instruction Manual Download Page 14 | Manualshive

Page: 14 / 14

MFJ Super Hi-Q Loop Instruction Manual Download Page 14

MFJ

Super Hi-Q Loop

™ Antenna Instruction Manual

14

If the slow tune buttons tune too fast to tune properly.

As above, adjustment of R26 is necessary. Adjust R26 for a slower pulse (LED blinks slower). Note
that improper adjustment of R26 will cause the problem above. Check for tuning on all bands before
reinstalling the cover.

If SWR is high due to close proximity to buildings, wires, trees, etc..

If SWR is high due to placement of the antenna, the feed loop in the antenna can be tuned (shaped) to
get a lower SWR.  Remove the bottom shell of the weather cover by removing the 20 screws holding it
together. Locate the feed loop, a loop of 10 gauge wire connected to a pcb at the feed point.  The loop
may be circular or elliptical. Compress or extend the loop until swr is at an acceptable level.  Replace
the cover.

TECHNICAL ASSISTANCE

If you have any problem with this unit first check the appropriate section of this manual. If the manual
does not reference your problem or your problem is not solved by reading the manual, you may call

MFJ Technical Service

at

601-323-0549

or the

MFJ Factory

at

601-323-5869

. You will be best helped

if you have your unit, manual and all information on your station handy so you can answer any
questions the technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road, Starkville, MS
39759; by FAX to 601-323-6551; or by email to [email protected]. Send a complete
description of your problem, an explanation of exactly how you are using your unit, and a complete
description of your station.

«
...
12
13
14

Summary of Contents for Super Hi-Q Loop















Reviews:

No comments