manualshive.com logo in svg

Metso 25411801001/A5684, Operation & Maintenance Manual

Share
Download
Metso 25411801001/A5684 Operation & Maintenance Manual Download Page 12

  
 
Slurry Pump 

 

 

WH06AAAAAA0EN_02B.DOC 

JAN 

04-W07 

Description

1/4

 

2 

DESCRIPTION 

2.1 

Product and warning signs 

2.1.1 

Product signs 

All product signs attached to the pump are shown below. 
 

 

Figure 2.1.1-1 Weight plate 
 
The weight sign is mounted next to the machine sign. When the pump is supplied without 
motor and drive, only the weight of the pump is stamped on the sign. In which case the 
total weight is stamped on the sign by the mechanic who fits the motor and drive on the 
pump. 
 

Pump delivered without motor 

 

Pump delivered with motor 

 

 

Space for CE-mark 
 

Pump type 

Pump number 

Year of manufacture

 

 

Figure 2.1.1-2  Machine plate 

A machine sign containing information as above is affixed to the pump. 
A pump delivered with motor has a machine sign with CE-mark. When the pump is 
delivered without motor the CE-mark has to be affixed when the motor is assembled.  
The CE-mark is included in the pump delivery. 
 

Motor weight

Drive weight

Pump weight

Total weight

Summary of Contents for 25411801001/A5684






















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands