Technical characteristics of the MX 5006
26
Benchtop multimeters, 6000 and 60000 points
Technical characteristics of the MX 5006 (continued)
AC and DC current
Warning
: the sum AC+DC must never exceed the range, 600mA, or 60mA, or
6000µA, or 6A, or 10A, as the case may be.
The AC component must represent at least 5% of the amplitude of the AC+DC total
for it to be possible to measure it.
A
AC+DC
TRMS
Range
Operating
range
Specified
measurement
range
Resolution
Uncertainty AC
40Hz à 20kHz
(
±
) (
**
)
Additional
uncertainty
DC (
±
)
Peak factor
Voltage
drop
Protection
6000µA
0 to
6000µA
60 to
6000µA
1µA
1.2% L +
0.08% x
[F(kHz)-1]L
±5 D
±15 D
2.6 to 5mA 25mV/mA
60mA
0 to
60.00mA
6.00 to
60.00mA
0.01mA
2.6 to
50mA
3mV/mA
600mA
0 to
600.0mA
60.0 to
60.0mA
0.1mA
1% L +
0.08% x
[F(kHz)-1)]L
±3 D
±13 D
2.6 to
500mA
0.58mV/mA
6A
0 to
6.000A
0.600A to
6.000A
0.001A
1.2% L +
0.08% x
[F(kHz)-1]L
±5 D
±10 D
2.8 to 5A 0.05V/mA
10A /20A
*
0 to
20.00A
0.60A to
20.00A
0.01A
1% L +
0.08% x
[F(kHz)-1]L
±3 D
±10 D
3.7 to 8A 0.05V/mA
Fuse
11A/1000V
> 20kA
The display indicates “OL” above 19.99A. The
symbol blinks and a beep sounds
above 10A.
Secondary measurements and displays: FREQ (AC coupling) MAX, MIN, PEAK
(
*
) Acceptable overload:
10A to 20A for 30s max. with a pause of 5min between 2
measurements. Ambient temp. 35°C max.
(
**
) Additional uncertainty with the 300Hz filter: see curve on p.29.
Frequency
Protection: 1414Vpk
Particular reference conditions: 150mV<U<600V
When the switch is set to Hz, the 300Hz filter is not in service.
Switch set to "Hz",
measurement of
the frequency
of a voltage
Range
Operating range
Specified
measurement range
Resolution
Intrinsic error
60Hz
10.00 to 60.00Hz
10.00 to 60.00Hz
0.01Hz
600Hz
10.0 to 600.0Hz
10.0 to 600.0Hz
0.1Hz
6kHz
0 to 6.000kHz
0.010 to 6.000kHz
0.001kHz
60kHz
0 to 60.00kHz
0.01 to 60.00kHz
0.01kHz
0.1% L ±1 D
Below 10Hz, or if the signal detection level is inadequate, the reading is forced to 0.
*
Measurement of the period in ms can be accessed using the
key.
Frequency voltage
or frequency current
simultaneously,
(secondary display)
Particular reference conditions:
150mV < U < 600V
0.15A
<
I
<
10A
Max. frequency measurable in volts:
60kHz
Max. frequency measurable in amperes: 60kHz
When the switch is set to V
LowZ
, Volts or Ampere, if the 300Hz filter is activated, the
measurable frequency remains within the limits of the PB of the filter.
Below 10Hz, or if the signal detection level is inadequate, the reading is forced to “----“.
