background image

11

FINAL WIRING and ASSEMBLY

1

2

3

4

5

6

Locate the factory wiring harness in the dash. Use the supplied wire harnesses 
and make the connection as shown. (Isolate and individually tape off the ends 
of any unused wires to prevent electrical short circuit.)

A

A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

B

D

C

99-7503

FINAL ASSEMBLY

Make wiring conections using the EIA color code chart shown below and the instructions included with the 
head unit. Metra recommends making connections as shown below;  Strip, Splice, Solder, Tape. Isolate and 
individually tape off ends of any unused wires to prevent electrical short circuit.

12V Ignition / Acc . . Red

12V Batt / Memory . Yellow

Ground. . . . . . . . . . . Black*

Power Antenna . . . . Blue

Amp Turn-On . . . . . . Blue / White

Amp Ground. . . . . . . Black / White

Illumination . . . . . . . Orange

Dimmer . . . . . . . . . . Orange / White

R

ight Front (+) . . . . . Gray

Right Front (-) . . . . . Gray / Black

Left Front (+) . . . . . . White

Left Front (-) . . . . . . White / Black

Right Rear (+) . . . . . Violet

Right Rear (-). . . . . . Violet / Black

Left Rear (+) . . . . . . Green

Left Rear (-) . . . . . . . Green / Black

*NOTE: 

When Black a wire is not present, ground radio to vehicle chassis. 

All colors may not be present on all leads due to manufacturer’s specifications.

METRA / EIA WIRING CODE

Plug the 5 way connector (supplied with the 99-7503) into location 1 on the back of the 
99-7503 housing (see diagram).

Plug the 16 way connector that you removed from the factory radio into location 2 on the back
of the 99-7503 housing (see diagram).

On manual climate control vehicles only, plug the 16 way connector (supplied with the 
99-7503) into location 3 on the back of the 99-7503 housing 
(see diagram). Automatic climate control vehicles will not use this harness. 

Re-connect the negative battery 
terminal and test the unit for 
proper operation.

Reassemble radio and dash
assemblies in reverse order of 
disassembly.

1

3

2

Summary of Contents for 99-7503

















Reviews: