background image

99-6527B

6

Axxess Interface Installation

•  Provides accessory power (12-volt 10-amp)
•  Retains R.A.P. (retained accessory power)
•  Provides NAV outputs (parking brake, reverse, speed sense)
•  Retains audio controls on the steering wheel
•  Retains safety chimes
•  Retains the factory backup camera
•  Retains the factory AUX-IN jack
•  Retains balance and fade*
•  Micro “B” USB updatable
* Non-amplified models only.

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape  
• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

•  Axxess interface (built into the touchscreen display)
•  6527 harness
•  16-pin harness with stripped leads
•  4-pin harness with yellow RCA jacks
•  Hazard harness
•  Female 3.5mm connector with stripped leads

Connections to be made

 ..........................................................................7-9

Installing the interface

 ............................................................................. 10

Initializing the interface

 ........................................................................... 10

Final assembly

 .......................................................................................... 10

Touchscreen display operation

 ...........................................................11-13

Steering wheel control settings

 ..........................................................14-15

INTERFACE COMPONENTS

TABLE OF CONTENTS

Summary of Contents for 99-6527B

















Reviews: