26
ENGLISH
−
Keep the supporting surfaces clean
– in particular, remove resin residue
with a suitable cleaning and mainte-
nance spray.
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A
Dust collection attachment
Protects your health and keeps the
shop clean.
B
Dust spout adaptor
To connect the dust collection
attachment to a dust collector.
C
Work clamp
Required for precision cuts and cut-
ting of non-ferrous metals.
D
Table extension, left
Required for cutting long stock;
extends to 3000 mm;
folds for space saving storage.
E
Table extension, right
Required for cutting long stock;
extends to 3000 mm;
folds for space saving storage.
F
Work stand
For a secure machine stand and
optimal working height;
folding, ideal for mobile use.
G
TCT saw blade 250 x 2.8 / 2.0 x 30
24 alternate bevel teeth
for wood and non-laminated parti-
cle board.
H
TCT saw blade 250 x 2.4 / 1.8 x 30
48 alternate bevel teeth
For wood and panels.
I
TCT saw blade 250 x 2.4 / 1.8 x 30
60 alternate bevel teeth
For wood, panels and thick-walled
plastic extrusions
J
TCT saw blade 250 x 2.8 / 2.0 x 30
80 trapezium-flat teeth
For wood, panels, ducting, NF
extrusion, high-quality veneered
sheets and laminates.
A
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
The machine's packing can be 100%
recycled.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine-free
bleaching process.
In this section problems and faults are
described which you may remove your-
self. If the measures detailed here do not
solve the problem, see under "Repairs".
A
Danger!
Many accidents happen partic-
ularly in connection with problems
and faults. Therefore please note:
•
Always unplug before servicing.
•
Check that all safety devices are
operational again after each fault
service.
Motor does not run
No mains voltage
•
Check cables, plug, outlet and
mains fuse.
No crosscut function
Transport locking pin engaged:
•
Pull transport locking pin out.
Safety lock engaged:
•
Actuate the safety lock.
Only little sawing performance
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material being
cut (see chapter "Technical specifica-
tions");
Saw blade warped:
•
Replace saw blade (see chapter
"Maintenance").
Saw vibrates heavily
Saw blade warped:
•
Replace saw blade (see chapter
"Maintenance").
Saw blade incorrectly mounted:
•
Mount saw blade correctly (see
chapter "Maintenance").
Saw squeals when starting
Drive belt tension too low:
•
Retension the drive belt (see chap-
ter "Maintenance - Drive belt ten-
sioning").
Stiffness of rotating table
Saw dust build-up under rotating table:
•
Remove saw dust.
11. Available accessories
12. Repairs
13. Environmental Protection
14. Trouble Shooting
15. Technical specifications
Voltage V
230 (1
∼
50 Hz)
110 (1
∼
50 Hz)
Current draw
A
8.4
15.9
Fuse protection
A
10 (time-lag)
-
Motor capacity* (power input P1, S6 20% - 5 min)
kW
1.8
1.6
Protection class
IP
20
20
Degree of protection
II
II
Saw blade speed
min
-1
5020 5020
Cutting speed
m/s
66
66
Saw blade diameter (outer)
mm
250
250
Arbor bore
mm
30
30
Dimensions
Machine in packing
−
Length / width / height
Machine ready to work, rotating table in 90°position, c/w suction port
−
Length / width / height
mm
mm
800 / 600 / 450
575 / 885 / 595
800 / 600 / 450
575 / 885 / 595
