5
English
By adjusting the dial, match the speed to the material and type of work.
Material
Grain
Dial scale
Rough grinding
Fine grinding
Paintwork:
Sanding
Repairs
(scratches, rust spots)
Stripping
180
120
40
400
240
80
3 – 6
2 – 4
2 – 4
Wood:
Softwood
Hardwood
Veneers
60 – 80
60
240
240
180
320
3 – 6
3 – 5
2 – 4
Metals:
Aluminium
Steel
Stainless steel
80
60
120
240
240
240
2 – 4
3 – 6
3 – 6
Note:
Please use this table as a standard.
PRACTICAL OPERATING PROCEDURES
CAUTION
Never apply water or grinding
fl
uid when sanding. This
could result in electrical shock.
1. Switching the sander ON and OFF
The power can be turned on by setting the lever to ON
(1) and turned o
ff
by setting the lever to OFF (0).
CAUTION
Never turn the power switch ON when the sander is
contacting the surface to be sanded. This is necessary
to preclude damage to the material. The same applies
when switching the power OFF.
2. How to hold the random orbit sander
While gripping the housing, lightly press the sander
against the surface to be sanded so that the sanding
paper uniformly contacts the surface, as shown in
Fig. 4
. DO NOT apply excessive pressure to the sander
while sanding. Excessive-pressure may cause overload
of the motor, reduced service life of the sanding paper,
and lowered sanding or polishing e
ffi
ciency.
3. How to move the random orbit sander
Move the sander by either moving it up and down or
by moving it in circles while gradually progressing in a
sideways direction (
Figs. 5 and 6
).
4. After installing new sanding paper
Movement of the sander may tend to become unsteady
after new sanding paper has been installed, because of
the new, coarse grain of the paper. This can be avoided
by slightly tilting the sander forward or backward during
sanding or polishing. Sander movement will become
steady as the sanding paper surface becomes properly
abraded.
MOUNTING THE OPTIONAL ACCESSORIES
○
Mounting the polyester bu
ff
Since the attachment is a hook-and-loop type as with
the sanding paper, the polyester bu
ff
can be mounted
by just pressing it onto the pad (
Fig. 7
).
MAINTENANCE AND INSPECTION
1. Empting and cleaning the Dust Bag
If the dust bag contains too much saw dust, dust
collection will be a
ff
ected. Empty the dust bag when it
gets full.
Remove the dust bag, open the fastener, and dispose of
the contents.
2. Inspecting the sanding paper
Since use of worn-out sanding paper will degrade
e
ffi
ciency and cause possible damage to the pad,
replace the sanding paper as soon a excessive
abrasion is noted.
3. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
4. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
5. Replacing supply cord
If the supply cord of Tool is damaged, the Tool must be
returned to metabo HPT Authorized Service Center for
the cord to be replaced.
6. Servicing
Consult an authorized Service Agent in the event of
power tool failure.
7. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair,
modi
fi
cation and inspection of metabo HPT
Power Tools must be carried out by a metabo HPT
Authorized Service Center.
This Parts List will be helpful if presented with the tool
to the metabo HPT Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
000Book̲SV13YA.indb 5
000Book̲SV13YA.indb 5
2018/02/07 15:23:25
2018/02/07 15:23:25
