Mestek SpacePak ESP-2430JV Installation, Operation & Maintenance Manual Download Page 3

Page: 3 / 36

RETURN AIR BOx (SPC-1D, AC-RBF-3, SPC-3D):

Each includes filter grill with metal frame, permanent

filter, and 2 clamp bands. SPC-1D is for ESP-2430JV. AC-

RBF-3 is for ESP-3642JV and SPC-3D is for ESP-4860JV.

RETURN AIR DUCT (SPC-4,5, & 6)

: Flexible, 10 feet

long with round shape. SPC-4 (15" dia.) for ESP-2430JV.

SPC-5 (19" dia.) for ESP-3642JV and SPC-6 (24" dia.)

is for ESP-4860JV .

PLENUM ADAPTOR

: 9" round OR 10" x 10" square

metal component to attach plenum duct to fan coil unit.

Plenum Adaptor - 9" Round - AC-PAJ

Plenum Adaptor - 10" x 10" Square - AC-PAJSQ

PLENUM DUCT & COMPONENTS:

May be 9" round

sheet metal or 10" x 10" (O.D.) square, fiberboard duct

types as specified by the installing contractor. Above

layout is shown as an illustrative assembly reference only.

SUPPLY TUBING (SPC-25-100):

Flexible, insulated,

2" I.D. and 3-1/4" O.D. Each section is 100 feet long.

R6 SUPPLY TUBING (AC-ST6-75):

Flexible, R6 insulated,

2" I.D. and 5-3/8" O.D. Each section is 75 feet long.

R8 SUPPLY TUBING (AC-ST8-50):

Flexible, R8 insulated,

2" I.D. and 6-1/4" O.D. Each section is 50 feet long.

INSTALLATION KITS:

Contains a specified amount

of sound attenuating tubes, kwik-connects, terminator

plates (incl. spring clips & screws), winter supply air

shut-offs and a balancing orifice set to complete

installation of room outlets. Supplied in (2) [AC-IKLT-2]

and (5) [AC-IKLT-5] outlet boxed quantities.

PLENUM TAKE-OFF KIT:

Contains a specific amount

of plenum take-offs, gaskets and fasteners to complete

installation of room outlets. Take-offs available for round

sheet metal or square fiberboard duct as specified by

installing contractor. Supplied in (2) [AC-TKMR-2] and

(5) [AC-TKMR-5] outlet boxed quantities for round sheet

metal and (2) [AC-TKFS-2] and (5) [AC-TKFS-5] outlet

boxed quantities for square fiberboard.

KWIK CONNECT WALL ELBOW (AC-KCWE):

To allow

for wall terminations in 2" x 4" stud spaces.

PLIERS (SPC-72):

To assure full setting of all clips

(fasteners) in plenum take-off (not shown).

PLENUM hOLE CUTTER (SPC-71-10):

To cut 2" hole

in fiber board for plenum take-off installation (not shown).

FIGURE 1.1: AIR DISTRIBUTION SYSTEM COMPONENTS

Summary of Contents for SpacePak ESP-2430JV





































Search results

Summary of Contents for SpacePak ESP-2430JV

Reviews:

Related manuals for SpacePak ESP-2430JV

Brands by name

Popular brands

Mestek SpacePak ESP-2430JV, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for SpacePak ESP-2430JV

Reviews:

Related manuals for SpacePak ESP-2430JV

Brands by name

Popular brands