manualshive.com logo in svg

Mestek SpacePak ESP-2430JV, Installation, Operation & Maintenance Manual

Share
Download
Mestek SpacePak ESP-2430JV Installation, Operation & Maintenance Manual Download Page 18

18

PLENUM

FASTENER

GASKET

PLENUM TAKE-OFF

GASKET

PLENUM TAKE-OFF

PLENUM

FASTENER

1. HAND INSERT FASTENER INTO PLENUM TAKE-OFF

2. WITH PLIERS, SNAP FASTENER INTO PLACE. 
    MAKE SURE IT IS FULLY SEATED

FIGURE 2.22: PLENUM TAKE-OFF FASTENER INSTALLATION

PLENUM

GASKET

FIGURE 2.21: TAKE-OFF INSTALLATION

FIGURE 2.23: ORIFICE INSTALLATION

Remove  the  hole  cut-out  from  the  plenum.  Make  sure

there is no “flap” left inside plenum that could block hole

during operation.

Place the plenum take-off gasket on the back side of the

plenum take-off and insert the assembly into the hole in

the plenum (see Figure 2.21).

NOTICE:  Gasket  must  be  installed  to  seal  plenum 

take-off to prevent air leakage.

Orient the plenum take-off to match the curvature of the

plenum  duct.  Hand  insert  the  four  plenum  take  off

fasteners one at a time such that each clip reaches the

interior of the duct. Using the SpacePak pliers, snap the

fasteners into place until they lock in place (see Figure

2.22).

NOTICE:  All  four  fasteners  must  be  installed  to

assure  an  air  tight  fitting  between  plenum  take-off

and plenum.

In accordance with your calculations as to requirements

for balancing orifices, mount the orifice in the outlet of the

plenum take-off (see Figure 2.23), prior to attaching the

supply tubing.

Next, install a kwik-connect in the open end of the supply

tubing, using the same procedures as before, and twist

together  kwik-connects  on  supply  tubing  and  plenum

take-off. Wrap connection securely with tape.

FIGURE 2.20: CONNECTING TUBING

Summary of Contents for SpacePak ESP-2430JV





































Reviews:

No comments

Brands by name

Popular brands

Load more brands