manualshive.com logo in svg

Mercusys MR1800X, User Manual

Share
Download
Mercusys MR1800X User Manual Download Page 25

17

Chapter 4  Configure the Router in Wireless Router Mode

•  IPTV/VLAN

 - Select to enable the IPTV feature.

•  Mode 

- Select the appropriate mode according to your ISP.

•  LAN 1/2/3

 - Assign your LAN port to whether function as the internet supplier or as the 

IPTV supplier.

4. 2. 6.  DHCP Server

By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the 
router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices 
from the IP Address Pool. You can change the settings of DHCP Server if necessary, and 
you can reserve LAN IP addresses for specified client devices.

•  To specify the IP address that the router assigns:

1. 

Visit 

http://mwlogin.net

, and log in with the password you set for the router.

2. Go to 

Advanced 

> 

Network 

> 

DHCP Server

 and locate the DHCP Server section.

1. 

Tick the 

Enable

 checkbox.

2. 

Enter the starting and ending IP addresses in the

 IP Address Pool

.

3. 

Enter other parameters if the ISP offers. The

 Default Gateway 

is automatically filled in 

and is the same as the LAN IP address of the router.

Summary of Contents for MR1800X





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands