manualshive.com logo in svg

Mercusys MR1800X, User Manual

Share
Download
Mercusys MR1800X User Manual Download Page 18

10

Chapter 4  Configure the Router in Wireless Router Mode

Click 

RELEASE

 to release the IP parameters.

•  MTU Size 

- The normal MTU (Maximum Transmission Unit) value for most Ethernet 

networks is 1500 Bytes. It is not recommended that you change the default MTU size 
unless required by your ISP. 

•  Host Name

 - This option specifies the name of the router.

•  Get IP with Unicast DHCP

 - A few ISPs’ DHCP servers do support the broadcast applications. If 

you cannot get the IP address normally, you can choose this option (it is rarely required).

Static IP

If your ISP provides a static or fixed IP address, subnet mask, default gateway and DNS 
setting, please select 

Static IP

.

•  IP Address

 - Enter the IP address in dotted-decimal notation provided by your ISP.

•  Subnet Mask

 - Enter the subnet mask in dotted-decimal notation provided by your ISP. 

Normally 255.255.255.0 is used as the subnet mask.

•  Default Gateway

 - Enter the gateway IP address in dotted-decimal notation provided by 

your ISP.

•  Primary/Secondary DNS 

- (Optional) Enter one or two DNS addresses in dotted-decimal 

notation provided by your ISP.

•  MTU Size

 - The normal MTU (Maximum Transmission Unit) value for most Ethernet 

networks is 1500 bytes. It is not recommended that you change the default MTU size 
unless required by your ISP. 

Summary of Contents for MR1800X





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands