Mercury Sterndrive QSD 2.0 Manual Download

Page: 18 / 131

Section 2 - Getting to Know Your Power Package

Page 10

90-8M0069751

eng

APRIL 2012

Bravo Sterndrive Serial Number and Identification

The Bravo sterndrive serial number, gear ratio, model number, and bar code are embedded in the ground plate on the port side

of the sterndrive.

33533

Bravo sterndrive information on ground plate

The serial number is also stamped as a permanent reference on the sterndrive casting inside the back cover.

33534

Bravo sterndrive serial number stamping

Bravo Transom Serial Number

The Bravo transom serial number is stamped into the U‑bolt plate of the transom assembly.

Bravo transom assembly U-bolt plate

a -

Transom assembly serial number

25904

Summary of Contents for Sterndrive QSD 2.0




































































































































Search results

Summary of Contents for Sterndrive QSD 2.0

Reviews:

Related manuals for Sterndrive QSD 2.0

Brands by name

Popular brands

Mercury Sterndrive QSD 2.0, Manual

Search results

Summary of Contents for Sterndrive QSD 2.0

Reviews:

Related manuals for Sterndrive QSD 2.0

Brands by name

Popular brands