Mercury 300 - PRO MAX 3.0L User Manual Download

Page: 72 / 79

TROUBLESHOOTING

ojc1

– STARTER MOTOR WILL NOT CRANK THE ENGINE

POSSIBLE CAUSES

•

Blown 20 Amp fuse in the starting circuit. Refer to Maintenance
Section.

•

Outboard is not shifted to neutral position.

•

Weak battery or battery connections are loose or corroded.

•

Ignition key switch failure.

•

Wiring or electrical connection faulty.

•

Starter motor or starter solenoid failure.

– ENGINE WILL NOT START

POSSIBLE CAUSES

•

Lanyard stop switch not in RUN position.

•

Incorrect starting procedure. Refer to Operating Section.

•

Old or contaminated gasoline.

•

Engine flooded. Refer to Operating Section.

•

Fuel is not reaching the engine.

a. Fuel tank is empty.

b. Fuel tank vent not open or restricted.

c. Fuel line is disconnected or kinked.

d. Fuel filter is obstructed. Refer to Maintenance Section.

e. Fuel pump failure.

Fuel tank filter obstructed.

•

Ignition system component failure.

•

Spark plugs fouled or defective. Refer to Maintenance Section.

Summary of Contents for 300 - PRO MAX 3.0L
















































































Search results

Summary of Contents for 300 - PRO MAX 3.0L

Reviews:

Related manuals for 300 - PRO MAX 3.0L

Brands by name

Popular brands

Mercury 300 - PRO MAX 3.0L, User Manual

Search results

Summary of Contents for 300 - PRO MAX 3.0L

Reviews:

Related manuals for 300 - PRO MAX 3.0L

Brands by name

Popular brands