background image

TO:                   ALL MERCEDES–BENZ PASSENGER CAR DEALERS 
DATE:               

February 2000   

 

REF. NO.          

P-SI-82.64/129

 

GROUP:           

82

 

Revision: 
SUBJECT:

           

MODEL 208.365/370

 

VOICE ACTIVATED CELLULAR TELEPHONE/CD CHANGER INSTALLATION 

 
 

 

 

Application Specific D2B Notes:

 

         

CD changer, telephone, and voice recognition module fibers are installed at the factory. Telephone and  

voice recognition fibers run along the left rear quarter panel and the CD fibers along the right rear quarter panel.

 

         

The vehicle is configured from the factory for the CD changer only.

 

         

Two sets of fiber cables run along the left quarter panel. One set is for the telephone only and the other for  

telephone and voice recognition. While not in the factory configured ring, these optics are coupled together  

just forward of the battery on the right. Which set of optics to use, will depend whether the telephone only or  

telephone with voice recognition will be installed.

 

         

All reconfiguration points are in the trunk in front of the battery and to the right of the fuse panel.

 

 

WARNING!

 

Disconnecting the negative battery cable is not recommended due to otherwise extensive 

reprogramming requirements. WIRING HARNESSES WILL BE ELECTRICALLY ACTIVE. IT IS 

THEREFORE NECESSARY TO EXERCISE EXTREME CAUTION WHILE EXECUTING THESE 

INSTALLATION INSTRUCTIONS. FAILURE TO DO SO, COULD RESULT IN SEVERE PERSONAL 

INJURY OR DEATH FROM ELECTRICAL SHOCK. The ignition and radio power must remain OFF until 

the final test is performed.

 

© 2005 Mercedes-Benz USA, LLC

Summary of Contents for 208.365




















Reviews: