Mendota FV44i-PF2 Installation & Operating Instructions Manual Download Page 4

 

SAFETY AND WARNING INFORMATION 

READ and UNDERSTAND

 all instructions carefully before starting

 the appliance. 

FAILURE TO

 

FOLLOW

 these instruc-

tions may result in a possible fire hazard and will void the warranty. 
 
Any safety screen or guard removed for servicing must be replaced before operating this appliance. 
 

DO NOT USE 

this appliance if any part has been under water. Immediately 

CALL

 a qualified service technician to inspect 

the appliance and to replace any part of the control system and any gas control, which has been underwater. 
 

THIS UNIT IS NOT FOR USE WITH SOLID FUEL

 
Installation and repair should be 

PERFORMED

 by a qualified service person. The appliance and venting system should 

be 

INSPECTED

 before initial use and at least annually by a professional service person. More frequent cleaning may be 

required  due  to  excessive  lint  from  carpeting,  bedding,  material,  etc.  It  is 

IMPERATIVE

 

that  the  unit’s  control  compart-

ment,  burners,  and  circulating  air  passageways 

ARE  KEPT  CLEAN

  to provide  for  adequate combustion  and  ventilation 

air. 
 
Always 

KEEP

 the appliance clear and free from combustible materials, gasoline, and other flammable vapors and liquids. 

 

NEVER OBSTRUCT

 the flow of combustion and  ventilation  air. Keep the front  of the appliance 

CLEAR

 of  all obstacles 

and materials for servicing and proper operation. 
 
Due to high temperature, the appliance should be 

LOCATED

 out of traffic areas and away from furniture and draperies. 

Clothing or flammable material 

SHOULD NOT BE PLACED

 on or near the appliance. 

 
Children and adults should be 

ALERTED

 to the  hazards of high surface temperature and should 

STAY AWAY

 to avoid 

burns or clothing ignition. Young children should be 

CAREFULLY SUPERVISED

 when they are in the same room as the 

appliance. 
 
These units 

MUST

 use one of the vent systems described in the Installing Your Fireplace section of the Installers Guide. 

NO OTHER

 vent systems or components 

MAY BE USED

 
This gas fireplace and vent assembly 

MUST

 be vented directly to the outside and 

MUST NEVER

 be attached to a chim-

ney  serving  a  separate  solid  fuel-burning  appliance.  Each  gas  appliance 

MUST  USE

  a  separate  vent  system.  Common 

vent systems are 

PROHIBITED

 
If the vent-air  intake system is disassembled for any  reason, reinstall per the  instructions provided for the  initial installa-
tion. 
 
The vent system assembly for this fireplace must be periodically examined by a qualified service agency. 
 

INSPECT

  the  external  vent  cap  on  regular  basis  to make  sure  that  no  debris  is  interfering  with the  airflow.    The flow  of 

combustion and ventilation air not to be obstructed 
 
DO NOT abuse the glass door by striking the glass, slamming the door shut, etc. 

Use only authorized parts and materials obtained from Johnson Gas Appliance Company when replacing defective or 
damaged glass.  
 

DO NOT USE

 abrasive cleaners on the glass door assembly. 

DO NOT ATTEMPT

 to clean the glass door when it is hot. 

 
Turn  off  the  gas  before  servicing  this  appliance. It  is  recommended  that  a  qualified  service  technician  perform  an  appli-
ance check-up at the beginning of each heating season. 
 

DO NOT

 place furniture or any other combustible household objects within 36 inches of the fireplace front. 

 

CAUTION:  Do not operate the appliance with glass removed, cracked or broken.  Replacement of the panel(s) should be 
done by a licensed or qualified service person.

Summary of Contents for FV44i-PF2





















































Reviews: