background image

 

35 

WASHERS (2)

3/8" COMP X 1/8NPT
BRASS FITTING

ORIFICE

PILOT LIGHT HOOD

MOTORIZED PRESSURE
REGULATOR

REAR ORIFICE
INSIDE HERE.

FRONT ORIFICE
INSIDE HERE.

WARNING:  It is of the utmost importance that the correct burner orifices be installed for both the rear and front 
burners. 

It is highly recommended that you remove the left side blower assembly and the left side exterior controls box 
before attempting to replace the pressure regulator. 

1.  Turn off gas supply at the appliance service valve.  
2.  See diagrams on this page and identify the Pressure Regulator on the 

Valve Body.

 

 

3.  Using a Torx T20 or a slotted screwdriver, remove 2 screws that secure 

the NG Pressure Regulator to the gas valve body and remove NG Pres-
sure Regulator, see following page.   

4.  Install the new LP Pressure Regular onto the gas valve body in the same 

position and orientation as the NG Pressure Regulator you removed in 
Step 2, above.  The LP Pressure Regulator can only be mounted in one 
position. Secure the LP Pressure Regulator in place.  Tighten down. 

5.  Remove both Rear and Front Burners.  Locate and Identify the Rear 

Burner Orifice Spud and the Front Burner Orifice Spud.  Both Front and 
Rear Orifice Spuds are removed and installed using a ½” deep well socket 
and ratchet. 

6.  Install Rear Burner Orifice #65-14-00054(#54 drill) for the Rear Burner. 

Tighten down securely. 

7.  Install Front Burner Orifice #65-14-00055 (#55 drill) for the Front Burner. 

Tighten down securely. 

8.  Locate Pilot Light on right side of firebox. While holding the pilot base 

body with large vice grips tightly, loosen Pilot Light’s hex shape base us-
ing a ½” open end wrench. Rotate counter clock-wise ¼ turn to loosen. 

9.  Pilot arrives from the factory set for NG. Push NG/LP Adjustment Clip in-

ward all the way to set it for LP. See detail view, below. If you see “NAT” printing on the Adjustment Clip, this indicates 
that the pilot is set to burn NG. Push Clip in so that “NAT” is not visible. 

10. 

Tighten down Hex shaped base of pilot using a ½” open end wrench. 

PRESSURE

REGULATOR

VIEW FROM OUTSIDE FIREBOX

 

Summary of Contents for FV44i-PF2





















































Reviews: