background image

11

TELEPHONE OPERATION (CONTINUED)

Make sure that the Caller ID service is
turned on by your phone company. When
you receive a call, the display will show
the name, number, time and date of the
caller between the first and second ring.

AM

TALMO, HOLLY

CALL #

1

See above section, “What Your Caller ID
Displays” if something other then the
caller’s information appears on the display.
The NEW CALL indicator will flash
when new call(s) have been received.

2

The display will indicate the total new
calls. When you want to check the calls
received, press the REVIEW (

)

button.

AM

TOTAL 03  NEW 01

3

You can also use the REVIEW (

or (

❷ 

button to cycle through the

past calls. Up to 80 numbers can be
stored in the caller ID memory.

2

1

4

RECEIVING A CALL WITH CALLER ID

WHAT YOUR CALLER ID DISPLAYS

NO CALL

: The caller memory is empty.

UNKNOWN CALLER

: The incoming

call does not have caller ID service or
the service area is not linked to yours.

PRIVATE CALLER

: The incoming call

is registered as “Private Caller” and
their information is withheld.

END OF LIST

: There are no additional

calls to be reviewed.

”: Low Battery Indicator

MC4285.O/M.QXD  1/3/02  1:36 PM  Page 11

Summary of Contents for MC4285




















Reviews: