Memmert ONE 10 Operating Instructions Manual Download Page 5

EXCELLENT

page 5

2  Technical data

Model

7

10

14

22

29

45

Volume [liter]

7

10

14

22

29

45

Usable bath length A [mm]

240

350

350

350

590

590

Usable bath width B [mm]

210

210

290

290

350

350

Usable bath depth C [mm]

140

140

140

220

140

220

Housing length D [mm]

468

578

578

578

818

818

Housing width E [mm]

356

356

436

436

516

516

Housing height (with flat cover) F [mm]

238

238

238

296

238

296

Housing height (with gable cover) G [mm]

337

337

347

405

343

401

Weight [kg]

11

14

16

17

24

26

Current consume [A]

5,2

5,2

7,8

8,7

10,4

12,2

Power [W]

1200

1200

1800

2000

2400

2800

 Ambient conditions

Ambient temperature 5°C - 40°C
rh max. 80% (no condensation)
Overvoltage Category: II
Contamination degree: 2

Setting temperature range

10ºC to 95ºC on waterbaths 
with activation of the  boiling mode to 100°C, see section 
4.3.1
20ºC to 200ºC on oilbaths

Setting accuracy:

0,1°C

Indication accuracy

0,1°C

 Working temperature range

From 5ºC above ambient temperature on water- 
and oilbaths or 15°C above ambient temperature 
on waterbaths with circulating pump to  nominal 
temperature = maximum temperature (see rating plate)

Summary of Contents for ONE 10





























Reviews: