background image

INSTALLING THE LP GAS CYLINDER (TANK) ONTO THE GRILL:

 

1.  

Check that the cylinder valve is closed by turning knob clockwise. Inspect cylinder valve rubber seal for 
cracks or deterioration. Do not use propane tank with damaged seal as a gas leak may occur.

2.  Place cylinder into tank holder in bottom of cabinet. 

3.  Orient cylinder so valve opening faces right side of the grill.

4.  

Fully tighten tank retention screw.

6

• 

Inspect propane tank valve rubber seal for cracks, wear 
or deterioration prior to use. A damaged rubber seal can 
cause a gas leak, possibly resulting in an explosion, fi re 
or severe bodily harm.

• 

Inspection should be done each time propane tank is 
connected to grill, has been refi lled, exchanged or has 
not been used for more than 60 days.

• 

Do not use a propane tank with a damaged rubber 
seal. Exchange tank or have rubber seal replaced at a 
qualifi ed propane fi lling station.

LP GAS CYLINDER (TANK) RUBBER SEAL INSPECTION:

GOOD
RUBBER SEAL

DAMAGED 
RUBBER SEAL

HOSE & REGULATOR SPECIFICATIONS AND INSTALLATION:

• 

DO NOT attempt to connect grill, as purchased for LP (propane) gas, to any other fuel supply 
source such as a natural gas line. For dual fuel grills that can be converted to natural gas, a 
3 Embers conversion kit must be purchased and installed for use with natural gas. 

• 

DO NOT use any other pressure regulator/hose assembly other than the one supplied with your 
grill. Replacement pressure regulator/hose assembly must be part No 9670-155-9670-0 which can be 
obtained by contacting customer service at 855-735-9922.

• 

DO NOT attempt to adjust or repair a regulator. The regulator is designed to operate at a 
maximum output pressure of 11 inches of water column (2.74 kPa).

• 

Ensure the tank valve is 

CLOSED

 prior to connecting the LP gas cylinder to your grill. Turn the 

valve knob clockwise to properly close the valve. Read and follow all instructions and warnings 
on the supply hose safety tags. Read and follow all warnings in this manual concerning the safe 
use of LP gas cylinders and the hose and regulator before connecting cylinder to grill. Read and 
follow all warnings on the LP cylinder.

WARNING

TANK RETENTION SCREW

Summary of Contents for GAS9670AS


































Reviews: