Mellanox Technologies Grid Director 4700 Installation Manual Download Page 25

Page: 25 / 88

Mellanox Grid Director 4700 Installation Manual



Port-to-port Latency - Under 100 nanoseconds



Data Virtual Lanes - 8



Management Virtual Lanes - 1



MTU - 4096 Bytes, max



Maximum hops - 1 hop between ports on the same board. 3 hops between different Line
Boards in the same chassis.

3.4

4700 Management Board (sMB-CM) Specifications

Two hot swappable Management Boards, each including on board CPU:

LEDs

Refer to

LED Indicators

(on page

Connectors

10/100/1000 Ethernet RJ-45, EIA/TIA-232 Console RJ-45

Reset button

Resets the Management Board or the entire chassis.

3.5

Chassis Slot Numbering

Slot numbering at the front of the chassis (for Management Board and Fabric Board) is from
left to right (indication on the horizontal fan unit sFU-40H).

Figure 9: sFU-40H Horizontal Fan Unit

Slot numbering at the rear of the chassis (for Line Boards) is from top to bottom (indication on
the cable guide brackets).

Summary of Contents for Grid Director 4700

























































































Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands

Mellanox Technologies Grid Director 4700, Installation Manual

Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands