manualshive.com logo in svg

Melec GD-5410, Instruction Manual

Share
Download
Melec GD-5410 Instruction Manual Download Page 6

Instructions Manual

１．Safety

１－１．Safety Precautions

(1) This product is not designed or manufactured for application for equipment

requiring high level of reliability such as equipment related to nuclear
energy, aeronautics-related equipment, automobiles, ships, medical appliances
directly handling the human body and equipment that might seriously affect
properties.

(2) Do not use or keep the product in explosive or corrosive environments, 

in the presence of flammable gases, locations subjected to splashing water, 
fine particles, soot, steam, or exposed to radiation or direct sunshine.
Doing so may cause electric shock, injury or fire.

(3) Do not transport, move, install the product, perform connections or inspections

when the power is on.
Doing so may cause electric shock.

(4) Only qualified personnel are allowed to transport, move, install the product, 

perform connections or inspections.
Failure to do so may cause electric shock, injury or fire.

(5) This product is for a devices inclusion.  

Please establish it into enclosure without fail.  
Be sure to ground the protective earth terminal of the driver.

(6) Do not touch the driver during operation or immediately after stopping.

Doing so may cause burn on the skin due to overheating of the driver.

(7) Ensure to use this product according to the method specified

in the Instructions Manual and within the specifications.

(8) Depending on the operational conditions, the stepping motor may step out when

it is on holding-state or driving-state.
In particular, the load in transport may fall if the motor steps out on the
vertical drive (such as the Z-axis).
Start operation after test run for deliberate confirmation of operation.

(9) Provide fail-safe measures so that the entire system may operate in a safe

mode even in cases of the external power supply failure, disconnection of the
signal line, or any failure on the driver.

     I  

     I  

-6-

Summary of Contents for GD-5410

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands