MELAG Sterilisator 205 User Manual Download Page 5

2 Safety

5

2  Safety

When operating the device, comply with the following safety instructions as well as those
contained in subsequent chapters. Use the device only for the purpose specified in these
instructions. Failure to comply with the safety instructions can result in injury and/or damage to
the device.

Qualified personnel

n

As with the preceding instrument decontamination, the sterilization of instruments using this steam
sterilizer may only be carried out by competent personnel.

Set-up, installation and commissioning

n

The device should only be set-up, installed and commissioned by persons authorized by MELAG.

n

The device is not suitable for operation in explosive atmospheres.

n

Check the device for any damage suffered during transport after unpacking.

Power cable and power plug

n

Only the power cable included in the scope of delivery may be connected to the device.

n

The power cable may not be replaced by a cable determined to be insufficient.

Danger of short circuit

n

Liquids may not be permitted to reach the interior of the device. This could result in an electrical shock
or short circuiting.

Preparation and sterilization

n

Do not place the objects to be sterilized on material produced from cellulose (e.g., paper, paper tow-
els, staple fiber, bandage material, etc.); this material would produce excessive heat accumulation
which would prevent the required heat equalization in the sterilizer.

n

Observe the relevant standards and directives for the preparation of instruments.

n

In the case of obvious or suspected damage/defects, the device may not be operated further. In such
cases, the device has to be repaired.

Transport and storage

n

Store and transport the device in a frost-free environment.

n

Avoid strong shocks/vibrations.

Repair

n

Never open the device housing. Incorrect opening and repair can compromise electrical safety and
pose a danger to the user. The guarantee and warranty are forfeited as soon as the device is opened
by anyone other than a MELAG-authorized technician.

n

The device may only be repaired by the manufacturer or an agency which he has authorized to do so
(stockist or customer services).

n

Only original MELAG spare parts may be used.

Summary of Contents for Sterilisator 205























Reviews: