3
H5/5 Pink Wire =
2-Step Door
Unlock Output
H5/5 Pink Wire =
Factory Security
Disarm Signal Output
H5/5 Pink Wire =
Start Status (Shock
Sensor By-Pass
Control) Output
4
H5/3 Black / Green
Wire Channel 4
Output =
Momentary output
H5/3 Black / Green
Wire Channel 4
Output =
Latched output
H5/3 Black / Green
Wire Channel 4
Output =
Latched output and
reset with ignition
“on”
H5/3 Black / Green
Wire Channel 4
Output =
Timer programming
(set to any interval
between 1 second
and 2 minutes.)
5
+
H7/4 White / Blue
Wire =
1 pulse activate
H7/4 White / Blue
Wire =
2 pulse activate
H7/4 White / Blue
Wire =
3 pulse activate
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Ground Output During Start (Crank) =
This wire will provide a 200mA ground output while the starter
output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire
found in some GM vehicles. This wire is also referred to as the ECM wake up wire in some vehicles.
Channel 4 Timer Control Output Programming.
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch
6
times and holding in on the
6
th
push until
three
chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature
‘III’
programming mode.
3. Press and release the transmitter
button 4 times, [4] LED flashes, [4] siren/horn chirps to indicate your
are in features “Channel 4 Timer Programming mode”.
4. Press and hold the valet switch, the timer will immediately start.
5. When the desired interval has passed, release the valet switch. One long chirp for confirmation.
(Set to any interval between 1 second and 2 minutes)
Note 1:
If your built-in timer controls window/sunroof closure in your car DO NOT change the timer setting! This
requires installer-only programming. Changing the value will adversely effect operation and may cause
damage.
Note 2:
Momentary output
= The momentary output selection will output a negative signal from the Channel 4 (5/6)
output immediately when the channel 4 (5/6) button is pressed and will continue until the button is release.
Latched output
= The latched output selection will output a negative signal as soon as the Channel 4 (5/6)
button is pressed and will continue until the button is pressed again.
Latched output / reset with ignition
= The latched / reset with ignition output selection operates just like the
latched output but will reset or stop when the ignition is turned on.
REMOTE START FEATURE PROGRAM MODE
START FEATURE “
I
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch
8
times and holding in on the
8
th
push until
four
chirps with a long chirp is hearing
then release the valet switch. You are now in the Start feature
‘I’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
Gasoline Engine
Diesel Engine and
10 seconds warn-up
timer
Diesel Engine and
15 seconds warn-up
timer
Diesel Engine and
20 seconds warn-up
timer
2
10 minutes run time
20 minutes run time
30 minutes run time
5 minutes run time
3
Factory alarm
disarm with channel
3 on
Without this feature
4
Constant parking
light output
Flashing parking
light output
13
