Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Comfort Feature:
Some Vehicles have a special “COMFORT feature”. When you lock the door with the key, you just have to
keep on turning the key on the door about 5 or 7 seconds and the window will close directly.
If your vehicle with “COMFORT feature” and you wish the door being locked and the window being closed
automatically at the same time by remote control, You can set the alarm feature
II-1
“with comfort feature”.
Password Pin Code Setup:
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch
4
times and holding in on the
4
th
push until
two
chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature
‘II’
programming mode.
3. Press and release the transmitter
and
button at the same time twice, [2] LED flash, [2] siren/horn
chirp to indicate your are in features “Password Pin Code Programming mode”.
4. Within 5 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet switch from
1 – 9 times.
5. Within 15 seconds of the last entered 9ths digit, turn the Ignition switch to “ON” position.
6. Within 15 seconds, enter your chosen second 9ths digit by pressing and releasing the valet switch from
1 – 9 times.
7. Finish by turning the ignition switch to “OFF” position.
If the new password code was accepted, the unit would report back the newly entered code, by flashing the
LED, first indicating the first digit code has been memorized, pause and then the second digit code. The unit
will report the new code three times with a one-second’s pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during
of above steps, the unit will revert back to the last successfully stored code. A [3] long chirps to confirm exit.
Will
revert back to the last successfully stored code
Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch
4
times and holding in on the
4
th
push until
two
chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature
‘II’
programming mode.
3. Within 15 seconds, press and hold
the
transmitter
and
button at the same time for 3 seconds. A
one long chirps to confirm Deleted the Password Pin Code.
Example: To program the Password Code 92, you would;
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the valet switch
4
times and holding in on the
4
th
push until
two
chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature
‘II’
programming mode.
3. Press and release the transmitter
and
button at the same time twice, [2] LED flash, [2] siren/horn
chirp to indicate your are in features “Password pin code programming mode”.
4. Within 5 seconds, press and release the valet switch 9 times.
5. Within 15 seconds of the last entered 9ths digit, turn the Ignition Switch to “ON” position.
6. Within 15 seconds press and release the valet switch two times.
7. Turn the Ignition Switch to “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in memory.
Exit:
Press any button of the transmitter to exit the password pin set up mode.
ALARM FEATURE “
III
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch
6
times and holding in on the
6
th
push until
three
chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘III’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
H2/4 Brown Wire =
Constant Siren
output
H2/4 Brown Wire =
5-second pulse Siren
output
H2/4 Brown Wire =
Horn Output
2
H5/1 White Wire =
Dome light Output
H5/1 White Wire =
Horn Output
H5/1 White Wire =
Factory Security
Rearm Signal Output
H5/1 White Wire =
Ground Output
During Start (Crank)
12
