background image

0330 999 2233

www.firedepot.co.uk

sales@firedepot.co.uk

Maintenance notes

We advise you to keep the equipment clean and to ensure the installation is in a dry and ventilated area. 

Checking that components are connected and their signal strength in 

Diagnostic Mode

To activate the diagnostic mode, press the transparent lens between the sounder and the callpoint on the 
master unit for 5 seconds.
The diagnostic mode is activated when the green LED of the master unit blinks.
Each connected unit beeps, the beeps correspond to the quality of the signal strength.
To end the diagnostic mode just press the transparent lens once.

Faults

 

       

Master unit Faults

 

       

A fault is identified by a flashing orange light on the master unit and a number of beeps on the master and/or the MCP.  

Number of beeps  Faulty Unit 

Fault  

 

Explanation

    

1    Master  

Battery  

 

The master unit battery is faulty  

2    Master MCP 

Battery  

          The master unit MCP battery is faulty  

3    MCP  

Battery  

 

An MCP has a faulty battery  

4    MCP  

Communication  

An MCP has a communication fault  

  

Manual call point (MCP) faults

 

       

Number of beeps  Faulty Unit 

Fault  

 

Explanation 

   

1    MCP  

Battery  

 

The manual call point battery is faulty 

2    MCP  

Communication  

No signal has been recieved from the  

 

Battery Fault 

     

Replace the defective Lithium 3Vcc CR 17 345 for the MCP including the One installed in the master unit. 
Replace the 9V 6 LR 61 battery inside the master unit.

Communication Fault

Go in to the diagnostic mode described earlier to check the quality and strengh of the signal, relocate if required or 
investigate if there is a new obstruction or interference causing the fault.

  

Clearing Configuration / Decommissioning

 

 

If at any point you are unsure of the number of MCP’s paired with the system, or are having problems commissioning, 
or wish to relocate the wireless system or reduce the number of paired units, then you will 

need to decommission 

the slaves one at a time. 

Both the Master P300W and D300W can not be decommissioned, however, the D300W 

can be moved and re-commissioned, using the normal procedureas set out in the step 3 to a different master

  

To decommission a slave P300W or a C300W, you will need to:

  

Press and hold the CONFIG button and the VALID button together until you here 3 short beeps, 4 long beeps and then 1 
short beep and then release the buttons, the C300W is now decommissioned from the system and can be added back 
using the normal procedure as set out in step 2. 

 

6

Summary of Contents for P300W








Reviews: