03282008
PROGRAMMING
A. PROGRAMMING TRANSMITTER:
Note:
This unit will only retain the last 4 remote transmitters programmed. If the transmitter memory is full, the
security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in the ON position. Within 15 seconds.
2. Push the Valet switch
3
times and hold it in on the
3rd
push until a long chirp is heard. Then release the
valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the
signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter.
Exit:
Turn Ignition to 'OFF' position, or leave for 15 seconds. 3 long chirps & 3 parking light flashes confirm exit.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE “
I
” PROGRAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch
2
times and hold it in on the
2
nd
push until
one
chirp with a long chirp is heard. Then
release the valet switch. You are now in the Alarm feature
‘I’
programming mode.
3.
Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change.
a.
Siren chirps and LED pause will indicate newly setting.
b.
System will advance to [2] LED flash, [2] chirp. (Factory default setting is always [1] LED flash, [1] chirp.)
4 Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
1
Chirps on
Chirps off
2
Automatic Rearm On
Automatic Rearm Off
3
/AUX
Instant Door Ajar Warning.
45 seconds Delay Door Ajar error chirp.
Exit
:
Turn the Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps are heard to confirm exit.
ALARM FEATURE “
II
” PROGRAMMING:
1
Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2
Push the Valet switch
4
times and hold it in on the
4
th
push until
two
chirps with a long chirp is heard. Then
release the valet switch. You are now in the Alarm feature
‘II’
programming mode.
3
Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
1
0.9-second Door lock
pulses.
3.0-second Door lock
pulse.
Double pulse unlock
2
Active arming
Passive arming without
passive door locking
Passive arming with
passive door locking.
3
/AUX
With ignition controlled door
locks & unlocks
Without ignition controlled
door locks & unlocks
Exit
:
Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
ALARM FEATURE “
III
” PROGAMMING:
1
Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch
6
times and hold it in on the
6
th
push until three chirps with a long chirp is heard.
Then release the valet switch. You are now in the Alarm feature ‘III’ programming mode.
3
Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
1
H1/4 Brown Wire = Siren
Output
H1/4 Brown Wire = Horn
Output
2
H3/6 Gray Wire = Trunk
(Channel 3) Output
H3/6 Gray Wire = Two
Step Door Unlock Output
H3/6 Gray Wire = Pager
Output
3
/AUX
Car Jacking Off
Car Jacking On
MEGA 470/474; VS 465/474L
7
