background image

Laminate Your Value

www.mefuchina.com

Installation and Notice

Before use

Check the chains and gears (at a regular time), clean and lubricate.

Using

The roller is hot during working, please do not touch it, in case of scalded
or bruised.

After use

Place the roller in the idle position, raised 5 mm above the working table.
Clean the roller at a regular time, do not use water to clean the machine
in case of short circuit, electric shock or rust.
Use 80% alcohol, detergent or eraser to clean the rollers after lamination,
which can lengthen the rollers' life.
1. The temperature of the roller should under 40

and stop heating.

2. Do not focus on one point.
3. Clean the residuum in time, otherwise it will affect the yields.

The MEFU Laminator should be assembled and used in a clean room with a
normal room temperature and normal humidity levels. The work place
should be dry and ventilated. Do not use this machine near water source or
wet ground. This minimizes the occurrence of static electricity. In the
meanwhile, do not close to combustible and explosive goods.

Delivery inspection

When the machine is delivered, the following units are included:

·

MEFU laminator

·

Manual

·

Accessories

Connections

Voltage: AC220/240V 50-60HZ

Positioning

The MEFU Laminator should be placed in a dry and ventilated situation.

Electrical connectors may only be
connected to socked to sockets
with the correct voltage. All other
operations may only be performed
by authorized.

Assembly

with

the

steps

performed

by

technician

authorized.

8

9

Summary of Contents for MF1700-F2













Reviews: