background image

INSTRUCTIONS PW530

2

1) Warnings

Please read this instruction manual carefully before the  

installation of gate-automated system.

This manual is exclusively for qualified installation 

personnel. Powertech Electronics Inc. is not responsible for 

improper installation and failure to comply with local 

electrical and building regulations.

Keep all the components of PW530 system and this manual 

for further consultation.

In this manual, please pay extra attention to the contents 

marked by the symbol:

Be aware of the hazards that may exist in the procedures 

of installation and operation of the gate-automated 

system. Besides, the installation must be carried out in 

conformity with local standards and regulations.

If the system is correctly installed and used following all 

the standards and regulations, it will ensure a high degree 

of safety.

Make sure that the gates works properly before installing 

the gate-automated system and confirm the gates are 

appropriate for the application.

Do not let children operate or play with the 

gate-automated system.

Do not cross the path of the gate-automated system when 

operating.

Please keep all the control devices and any other pulse 

generator away from children to avoid the gate-automated 

system being activated accidentally.

Do not make any modifications to any components except 

that it is mentioned in this manual.

Do not try to manually open or close the gates before you 

release the gear motor.

If there is a failure that cannot be solved and is not 

mentioned in this manual, please contact qualified 

installation personnel.

Do not use the gate-automated system before all the 

procedures and instructions have been carried out and  

thoroughly read.

Test the gate-automated system weekly and have 

qualified installation personnel to check and maintain the 

system at least every 6-month.

Install warning signs (if necessary) on the both sides of 

the gate to warn the people in the area of potential 

hazards.

Summary of Contents for PW530













Reviews: