Medical Solutions 6000 Series Operator'S Manual Download Page 11

 

5640.A 

 

11

LIMITED WARRANTY 

 

 
For one year from the date of shipment to the Buyer (the “Warranty Period”), MSI warrants that the Equipment 
provided to the Buyer shall be free from defects in workmanship and material.  In the event of a breach of this 
warranty during the Warranty Period, MSI shall, at its option, repair or replace the Equipment, and Buyer’s remedies 
are limited to such repair or replacement.  MSI DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED OR 
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE.  IN NO EVENT SHALL MSI BE LIABLE FOR DIRECT, INDIRECT, PUNITIVE, ECONOMIC, 
CONSEQUENTIAL OR OTHER DAMAGES, INCLUDING BUT NOT LIMITED TO LOST PROFITS. 
 
To enable MSI to administer the Warranty properly, Buyer shall (1) register the Warranty using the form provided 
below, and (2) promptly notify MSI of any claim hereunder.  As a condition to the Warranty, Buyer shall use and 
maintain the Equipment according to the provisions of the Operator’s service manual.   

 
 

IMPORTANT: THIS IS YOUR TEMP 2

®

 WARRANTY REGISTRATION 

 
 
Please register your warranty by filling out this page and send it to Medical 
Solutions, Inc. within 30 days of purchase. 
 
A. 

Hospital Name:       

 
B. 

Mailing Address:    

 
C. 

City:    

State:    

Zip Code:         

 
D. 

Contact Name:        

 
E. 

Date Purchased:      

 
F. 

Serial Number:        

 
G. 

Department Purchased For:       

 

COPY THIS PAGE AND MAIL TO: 
 
Medical Solutions, Inc. 
3901 Centerview Drive, Suite L  
Chantilly, Virginia 20151 
Fax number 703-834-0039

 

 

Summary of Contents for 6000 Series












Reviews: