manualshive.com logo in svg

Mect TPAC1008 03 Series, User Manual

Share
Download
Mect TPAC1008 03 Series User Manual Download Page 29

HMI PLC all in one: TPAC1008 03                                                               Mect srl 

 

ME7068_05    11/19

 

27 

 

 

 

 

PLC_BUZZER 

Buzzer 

RW 

enable dynamic buzzer sound 
(0x44332211 up=0x11(%) on=0x22(cs) 
off=0x33(cs) rep=0x44(times)) 

CH0_NETRUN 

active channel 

RO   

CH0_NETGOOD 

channel 
configuration 

RO   

CH0_NETERR 

bus status 

RO   

CH0_NETRST 

bus reset 

RW   

CH0_NETDIS 

disable the bus 

RW   

CH0_01_NODERUN 

In Out board - 
active channel 

RO   

CH0_01_NODEGOOD 

In Out board - 
channel 
configuration 

RO   

CH0_01_NODEERR 

In Out board - bus 
status 

RO   

CH0_01_NODERST 

In Out board - bus 
reset 

RW   

CH0_01_NODEDIS 

In Out board - 
disable the bus 

RW   

 
After that the variables are available in read / write mode as described in the program 
tutorial. The system can use 5472 interchange variables between HMI and automation 
(at maximum) which include: 
internal variables, interchange variables on Modbus network, retentive variables.  
The variables are defined by a software “Mect Suite”. 
 

 

7.

 

 How to order 

 

Summary of Contents for TPAC1008 03 Series






























Reviews:

No comments

Brands by name

Popular brands

Load more brands