background image

For Outdoor Household Use Only. Not for Commercial Use.

Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?

Visit us online at www.AussieGrills.com Or call Aussie Customer Service at 1-800-251-7558

• Failure to follow these intructions could result in 

fire or explosion which could cause death, serious 
personal injury, or property damage.

• Read and follow instructions carefully before as-

sembly or use.

• Do not use this product for any other purpose than 

which it is intended.

• These instructions must be kept with the user. 

SAVE THESE INSTRUCTIONS.

If you smell gas:

1. Shut off gas to the appliance.
2. Extinquish any open flame.
3. Open lid.
4. If odor continues, keep away from the appli-

ance and immediately call your gas supplier or 
your fire department.

WARNING

DA N G E R

!

!

LP Gas Grill Assembly and Use Manual

67C3C8KK81

67C3C8LK81

67C3C8MM81

• Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 
other appliance.

• An LP cylinder not connected for use shall not be 

stored in the vicinity of this or any other appliance.

WARNING

!

With the 

NEW Aussie

FLAVOR ACTIVATOR SYSTEM

(Patent Pending)

Provides:
- More even heat on the cooking surface
- Hotter temperature with the same fuel usage
- Longer cooking for the same amount of fuel

Summary of Contents for Assie Vantage 67C3C8KK81 Use





































Reviews: