background image

page 4

3. PREPARATION BEFORE TEST

Choose appropriate accessory and attach to gauge
a) Pull Test

Choose test hook and attach to the load application rod marked 

[PULL].

b) Push Test

Choose appropriate accessory from items supplied and attach to the load application rod 
marked 

[PUSH].

c) Use of extension rod

The extension rod can be used on either the 

[PUSH]

or 

[PULL]

application rod.

NOTE:
When using the extension rod ensure that the load is applied axially to the gauge in
order to maintain the accuracy.

a) 

[PEAK]

change to 

[TRACK]

Press button while at the same time rotating anti-clockwise until the 

[TRACK]

is reached.

b) 

[TRACK]

change to 

[PEAK]

Turn button clockwise until the 

[PEAK]

position is reached.

c) After Testing

After testing is complete return the button to the 

[PEAK]

position, this helps to extend the life of

the internal mechanism.

a) Ensure that the indicator dial is rotated to 0 for the start of the test. This can be achieved by 

turning the indicator dial clockwise or anti-clockwise depending on the initial position.

b) When using the gauge vertically ensure that the indicator dial is rotated to 0 after any 

accessories have been attached.

NOTE:
Ensure that the capacity of the gauge to be used is suitable for the application. If the
gauge is constantly taken over its designed operating range it may sustain damage and
the reading will be unreliable.

4. OPERATION OF PEAK HOLD RELEASE AND TRACKING BUTTON

5. ADJUSTMENT OF INDICATOR DIAL

Summary of Contents for AN Series













Reviews: