background image

Mobile Hand Wash Station

REVISION: 07/2020  |  page 12 of 16                                                                                        INSTALLATION & OPERATING MANUAL

 

Chapter 7.   OPERATING INSTRUCTIONS 

7.1  Models BSX-MHB-HCW and BSX-MHB-HCW-T 
Important!  Following installation, the time flow valve needs to be primed to  

remove air from the hose.  
Actuate time flow valve by compressing and releasing by foot. At 3 bar water  

pressure, each actuation will provide a run time of 8 to 12 seconds. Repeat  

as necessary. 

 

 

 

 

 

7.2  Model BSX-MHB-X 
Important!  Following installation, or following water container refill, the manual  

foot pump needs to be primed to remove air from the hose.  
Actuate manual foot pump by compressing and releasing. Each compression will  

deliver water to the spout. Repeat as necessary. 

7.2.1  Remove empty water feed container. Lift out feed hose.  

7.2.2  Lift flexible waste hose out of waste container. 

7.2.3  Remove waste container from unit. Ensure container screw cap is replaced. Dispose of waste water. 

NOTE:

 Be careful to manoeuvre the containers around the flexible waste fittings to prevent damage. 

NOTE:

 Waste water is dirty and must be disposed of responsibly. 

7.2.4  Ensure empty waste container is replaced into the LHS of the unit with neck facing front and screw cap 

removed. Reinsert flexible waste hose into neck of the container.  

7.2.5  Once refilled, replace water hose into fresh water container and reinsert into the RHS of the unit with the 

neck of the container facing the rear.  

NOTE:

 Be careful to manoeuvre the containers around the flexible waste fittings to prevent damage. 

NOTE:

 When transporting full water containers ensure screw cap is fitted. 

7.2.6  Following each water container refill manual foot pump needs to be primed to remove air from the hose.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Basix BSX-MHB-HCW

















Reviews: