background image

4

At the front of the tent, slip the front arch pole over the side arch poles. 

Fit the pole ends into the grommets at the side corners of the tent. Attach 

the remaining clips to the front arch pole. For maximum stability, attach 

the bottommost clip on each side to the front arch pole just above the 

point where it crosses over the side poles. This pulls the poles closer, 

allowing them to brace against one another.

7

 Spread the fl y over the tent body with the webbing colours on the 

fl y corners matching the webbing colours on the tent fl oor corners (the 

scooped vent on the fl y goes in front of the door in the tent body).

8

 

On the underside of the fl y are four Velcro® wrap-ties. 

Attach all the wrap-ties.

 It is easiest to attach them in the following order:

One wrap-tie goes around the centre of the front arch pole, at its highest 

point. Two more wrap-ties go around the two junctions where the front 

arch pole and the longer side poles cross. The fi nal wrap-tie goes around 

the junction of the two long poles at the back of the tent. Note: at 

these pole junctions, fasten the wrap-ties around both poles as tightly 

as possible; this will maximize the tent’s strength by bracing the poles 

against each other. 

To do this: wrap the longer Velcro tab horizontally 

twice around both poles, pull on the tab end to cinch it tight, then secure 

it by folding the shorter Velcro tab over it.

9

  Fit all six webbing tabs onto the appropriate pole tips, over the webbing 

grommets from the tent body as shown in fi gures A and B. Fold the tabs 

under the body of the tent as you go.

The basic set-up is now complete. 

Staking and Tensioning the Tent 

Even freestanding tents should be pegged to avoid them blowing away 

and to permit proper ventilation. At a minimum, peg out the two back 

corners of the tent and the two front corners of the vestibule.

The Tarn 3 has anchor loops and external guy points for even more secure 

anchoring in windy conditions. First anchor the corners of the fl oor with 

pegs. If you have not already done so, attach the Velcro wrap-ties on the 

fi gure A

fi gure B

Tarn3 eng.indd   4

Tarn3 eng.indd   4

3/4/05   3:49:29 PM

3/4/05   3:49:29 PM

Summary of Contents for Tarn 3









Reviews: