background image

2

 

SEAM SEALING

The seams of your tent have been waterproof taped on all exposed 

seams. All features, such as Velcro® pole anchors and door tiebacks, have 

been welded onto the inside of the fl y to avoid any small leak points. 

However, for extremely wet and windy conditions, you may want to re-

seal selected parts of your tent. These include parts of the inner tent 

where condensation or windblown rain could potentially wick through, 

such as lantern loops or pole clip suspension points. You may also wish to 

seal the “in” side of any untaped fl oor seams exposed to ground moisture 

or rainfall. For seam sealing and tent repairs, we recommend a quality 

after-market polyurethane sealer such as McNett Seam Grip®.

Work in a well-ventilated area to avoid inhaling sealant vapours. For 

complete sealing, evenly apply only the minimum required amount of 

sealant into needle holes, thread, and fabric joints. Allow to dry and cure 

overnight. McNett sealants (Seam Grip, and similar) cure more quickly in 

a moist or humid environment. Before packing the tent for the fi rst time, 

dust newly sealed areas with talcum powder or spray them with 303

TM

 

Protectant; freshly cured sealer can bond to itself even when dry. If the 

tent is used hard and often you may need to reapply seam sealer in high-

wear areas.

 

SITE PREPARATION

Remove sharp objects that might puncture the tent fl oor.

A ground sheet beneath the tent is not necessary for waterproofness, 

but it will reduce long-term wear on the tent fl oor. A ground sheet should 

be cut or folded smaller than the tent fl oor to prevent water pooling 

between the fl oor and the ground sheet. Another light and convenient 

option is MEC’s custom-made, coated nylon Footprint.

In winter conditions, we recommend digging out a platform with 

surrounding walls. To avoid melting depressions in the snow under the 

tent, pack the snow down solidly by ski or foot.

Tarn3 eng.indd   2

Tarn3 eng.indd   2

3/4/05   3:49:27 PM

3/4/05   3:49:27 PM

Summary of Contents for Tarn 3









Reviews: