Me ADF-501 EX, Operating Instructions Manual

Page: 11 / 28

GB
ENGLISH | ADF-510
11
3.2. OUTDOOR UNIT (only suitable for surface mounting)
Step 1: Find a suitable location for the outdoor speaking unit.
Step 2: Drill the mounting holes with a diameter of 6mm into
the wall using the drilling template.
Step 3: Place one dowel in each of the 6mm holes.
Step 4: Remove the screw (10) on the outdoor station in order
to be able to remove the front casing section
from below.
Step 5: Insert a screw into the upper hole in the wall. The
head of the screw should stand out by
approximately 3mm.
Step 6: Hang the outdoor unit on the screw and secure the
outdoor unit with a screw through the hold in the
battery compartment.
Step 7: Hang the front casing section over the rear casing and
replace both screws (10).
Personalise the nameplate
1. Carefully lever the cover off the nameplate using a screwdriver.
2. Remove the paper and write on it (e.g. your name).
3. Replace the paper into the nameplate cover and press it with
slight pressure onto the bell push.
Power supply to the system
The outdoor station can either be powered with 3 C cells or with a
standard bell transformer (8V AC/ 1A).
Either insert the 3 batteries correctly into the battery compartment or
connect the 8V from your bell transformer onto the terminal (14) on
the back of the casing.
4. INITIAL OPERATION
Switching the handset on
• Slide the power switch (5) to the “ON” position.
Switching the handset off
• Slide the power switch (5) to the “OFF” position.
Battery monitoring
a. Outdoor speaking unit: If the battery is empty the outdoor
station will send a signal to the handset. The LED (4) on the
handset will then flash.
b. Handset: If the storage battery is empty the LED (2)
will flash rapidly.
Operation
1. Press bell push at the external station.
2. A melody is played for 30 seconds at the receiver, the luminous
surround around the talk button flashes green.
3. Press and hold down the talk button within these 30 seconds
to speak to the visitor; the luminous surround around the talk
button turns red while the button is held down.
4. Release the talk button to hear the visitor‘s response; the
luminous surround around the talk button turns green.
5. Repeat steps 3 and 4 to have a conversation with the visitor.
6. At the end of the conversation, press the talk button twice in
quick succession.
Notes on operation
1. The melody plays for around 30 seconds; after this time the
receiver returns to standby mode.
2. If, at the end of a conversation, the talk button is not pressed
twice in succession so as to hang up, the receiver automatically
enters standby mode after 20 seconds.
3. A visitor will not be able to hear you unless you press
the talk button.
Selecting the receiver melody and the melody volume
1. Turn the handset off using the switch (5).
2. Press and hold the volume button (5.1) to increase the volume
and turn the handset back on using the switch (5). Keep pressing
the volume increase button (5.1).
3. If the power LED lights up green release the volume
increase button (5.1).
4. If you press the press to talk button (3) once, the melody that
is currently set will begin to play.
5. If you briefly press the volume increase button (5.1) the next
melody begins to play.
6. If you briefly press the volume decrease button (5.2) this will
alter the volume. 3 volume levels are available.
7. Press the press to talk button (3) on the handset briefly in order
to save the melody and volume as set.
There are 8 different melodies to choose from.
Charging the storage batteries on the indoor station
1) Connect the base station to the power adaptor.
2) Place the handset into the base station. The LED on the base
station will light red throughout the charging process and then
turns green once charging is complete.
3) The charging process will be complete after approx. 3 hours.